Posts Tagged ‘Wood Floors’

Wood Floor Cleaning: Removing Rejuvenate or Orange Glow From your Floors

Tuesday, January 11th, 2011

Removing products like Rejuvenate or Orange Glo from your wood or laminate floors can be a very tough, costly and fustrating  job if you don’t know what you are doing. If you are planning on getting new floors, I recommend you check out perth flooring solutions. They have high quality flooring for great prices. But before replacing your floors, make sure to have an expert in waterproofing services take a look and do the necessary action.

We recently had a customer hire us to clean and remove the product “Rejuvenate” from her new laminate floors which had caused an uneven and blotchy sheen. We were able to remove the product and clean her laminate floors following these commercial cleaning steps

Products needed:

  1. • Spray bottle (optional)
  2. • Scotch-Brite abrasive pad (green scrub pad with yellow sponge-NOT an SOS, Brillo or steel wool pad)
  3. • Soft towels
  4. • New and well rinsed sponge mop OR terrycloth mop
  5. • Rubber/latex gloves and safety goggles (recommended to prevent eye/skin irritation when handling IFT)

Process

It’s best to begin with a test section in an inconspicuous area (i.e. behind a door). We recommend working in

small sections as you complete this process. Complete all steps before moving onto another section of the

floor.

1. Apply a SMALL amount of the IFT solution to a section of the floor. Use a spray bottle to mist the floor. Purchase liquid floor coatings and products from the reliable adhesives lab epoxy flooring supplier.

or squirt a small amount and spread it with a soft cloth. Apply only enough cleaner to wet the floor.

2. Use the abrasive pad and scrub the area. This should remove the wax buildup, you can also use the services from Shark cordless vacuum to get a deep cleaning.

3. After scrubbing the area, wipe the section with a water dampened cloth.

4. The final step is to apply Squeaky Cleaner with a microfiber mop. No water rinse is necessary after this

cleaner is applied. Wipe/mop the floor until it is dry – do not leave the floor wet.

If this is successful in removing the contaminant, proceed with the rest of the floor, following all steps. You may

need to repeat steps 1 & 2 more than once.

If you are not successful in removing the contaminant with this process, you need to remove the remaining

product by abrading the floor (screening or sanding). It is recommended to hire a professional flooring

contractor if abrasion techniques are required. If you want to find out more tips for your floors and home, visit here and don’t miss out on the best tips on how to keep your floors clean and shiny.

For help with commercial cleaning or refinishing wood or laminate floors in Tampa, FL  contact National Cleaning Specialist at 813-431-1331

Or follow this link www.NationalClean.com

Does Your Wood Floor Need to be Recoated or Refinished?

Thursday, March 4th, 2010

A complete refinishing may be necessary

National Cleaning Specialist of Tampa Bay recommends if areas of your floor have been worn down to the bare wood, if the floor has deep stains or color differences in the wood, if there’s chipping or peeling, or if your floor cannot be re coated due to factors discussed above, you’ll have to do a complete refinish.

If these signs are not readily apparent,you can use this simple test to determine what care your floors need:

  • Take this simple test
  • Find a high traffic area where the finish is likely to be the most worn, and pour a tablespoon of water onto the floor.
  • If the water beads up and you can wipe it without a trace, the finish is still working and you don’t need to do anything just yet.
  • If the water slowly soaks into the wood floor, creating a moderately darkish spot, the floor is partially worn. You may be able to get away with a recoating. Consult your wood flooring contractor for the best course of action.
  • If the water immediately disappears into the wood leaving an obvious dark spot, it’s time to refinish the floor.

For routine cleaning of wood floors by sweeping and vacuuming along with use of Squeaky Cleaner will maintain the floor’s original appearance. We also work with a recycling system, one option is bin hire Sydney they offer the best waste management service in Sydney, can be trusted with the removal of wastes from your homes and offices, so we can manage the furniture you don’t use or want, we work with Be Equipment for the recycling machinery so we will take care of yours !

There are a variety of textured floors, with each one offering a different coefficient friction.  The coefficient friction is the test result of how slippery a floor rates.  The higher the coefficent friction, the higher the slip-resistance.  There are a variety of aggregates that epoxy flooring contractors can broadcast into the uncured material: quartz sand, aluminum oxide, walnut shells, and glass beads.  Each one serves a different purpose, so it’s important that the estimator knows which material to use in each situation. Epoxy Floors NYC can install your commercial epoxy floor coating affordably and within a set time frame so as to cause minimal interruption to your working day.

National Cleaning Specialist serving Tampa,FL. since 1991

Call Now for Same Day Cleaning and Polishing 813-907-9092

Wood Floor Cleaning only $40 per room up to 100 Sq. Ft. 2 Rm Minimum


“Basic Coating”